extend your senses
KOS
BIMETAL SWITCHES WITH THREAD AND CABLE TSB 060

BIMETAL SWITCHES WITH THREAD AND CABLE TSB 060

BIMETAL SWITCHES WITH THREAD AND CABLE TSB 060

CONFIGURATOR

CONFIGURE AND REQUEST

22830
__KOUPIT__
__NABIDKA__
__JINY DOTAZ__

BBB

--%>

Series TSB 060 bimetal temperature sensors are designed as two-state controllers (ON/OFF control) that compare the preset and instantaneous temperature and immediately disconnect the contact when a defined temperature is reached. The required temperature is defined according to the customer’s needs by the selection of a bimetal thermal cutoff and cannot be changed.

Bimetal switches TSB 060 series consist of a stainless steel housing containing a bimetal switch (thermal cutoff) and supply cable.

Bimetal switches TSB 060 series are used to signal exceeded temperature in various industrial applications, e.g. to protect transformers, power semiconductor stages, motors and powerful batteries. The Bimetal switches TSB 060 series are intended for operation in chemically non-aggressive environments.  

DECLARATION, CERTIFICATION, CALIBRATION

  • Manufacturer provides EU Declaration of Conformity.
  • Calibration – The final metrological inspection – comparison with standards or working instruments – is carried out for all the products. Continuity of the standards and working measuring instruments is ensured within the meaning of the Section 5 of Act no.505/1990 on metrology. The manufacturer offers a possibility to supply the sensors calibrated in SENSIT s.r.o.’s laboratory (according to requirements of the EN ISO/IEC 17025 standard) or in an Accredited laboratory.  

 

Technické parametry

Switch type TSB 060
Temperature switch sensing element Bimetal TMC – C1B
Temperature range
(selection of the tripping temperature)
70 to 180 °C (in 10 °C steps)*
Switching tolerance ± 5°C
Contact design normally closed (snap action)
Maximum switching voltage/current 10.000 cycles 250 V AC / 2,5 A
3.000 cycles 250 V AC / 6,3 A
Case material stainless steel DIN 1.4301
Case diameter 10 mm
Case length 35 mm include thread
Thread type / OK
M14 x 1.25 / OK17
Working range -25 to 180 °C
Ingress protection IP 67 in accordance with EN 60529
Insulation resistance
in normal environment
min. 20 MΩ
Dielectric strength of insulation 2 kVAC/1 min.
Contact connection 2wire
Supply cable silicon shielded 2 x 0,34 mm2
Weight min. 0,2 kg acc. to design

Note: Manufacturer reserves the right to make changes in design and technical characteristics of the products. For actual information, please always contact your dealer.

Rozměrový náčrt

Schéma zapojení

Modifikace

Soubory ke stažení

128.01en.pdf 128.01en.pdf

Related Products

TEMPERATURE SWITCHES TSDD

Detail Detail

TEMPERATURE SWITCHES TSZ4H

Detail Detail
1
 
2
 
3
*
 
4
*

CONTACT

SENSIT s.r.o.

Školní 2610, 756 61 Rožnov pod Radhoštěm


+420 571 625 571

c883110a-27c4-4109-b434-8fc90a707e06

NEWSLETTER

Receive news and product information in your email.

© Copyright 2022 SENSIT s.r.o. | Školní 2610, 756 61 Rožnov pod Radhoštěm, Czech Republic | +420 571 625 571 | 635f439b-3598-4a4b-8c05-2f892f0d5151
All Rights Reserved. Webdesign: FlexiSystems s.r.o.: e-learning, webdesign, CMS.
...